1 to 16 channel datarecorder / datalogger with modular inputs

Random configurations possible, 1 to 16 inputs, choice of 30 different input modules

Memory for 480.000 readings Automatic downloading to PC if required

Communication via RS232, RS485, modem or GSM modem

High system accuracy because of 16 bits A/D conversion

Easy installation and configuration the system is virtually "plug & play"

Extensive alarm possibilities audible, visual and via relay outputs

General specifications

Go to Software
section

Go to Sensor
section

Material enclosure:
No. of inputs

Operating limits
Clock:
A/D conversion
Sample rate:
Memory capacity:
Recording methods:

Protection grade:
Sensor connection:

LED indicators:
(MS3+ / MS4+)

Mounting:
System requirements

Polycarbonate
16 free input slots, random configurable
(see list of available input modules)
0 to +50°C
real-time clock
16 bits
selectable in fixed rates from 1 sec. to 24 hours
~480.000 analogue readings
- stop-when-full,
- first-in-first-out
IP2x
- standard removable Wago connector
- sub-miniature thermocouple connector in
combination with a thermocouple input module

- mains power
- when exceeding alarm limits (2 per channel)
- when exceeding 75% of memory capacity
- when memory is full

ATM system will be supplied with wall brackets
Windows® 95/98/NT/2000/XP, VGA color monitor, 10Mb harddisk space and 64Mb RAM recommended

The MS+ systems are stand-alone, modular, 1 to 16-channel data recorders. They can be completely configured according to your wishes. The basic unit has 16 free input slots and can be expanded with input modules. There is a choice from 30 different input modules, optical or non-optical isolated. When ordering, the desired configuration should be indicated. The systems are developed for stand-alone recording of temperature (using PT100, PT1000, Ni1000, and thermocouples), alternating current, AC voltage, DC process signals (mA, volt), pulses (status or counts), etc. Sensors with an output signal (e.g. for temperature, relative humidity or pressure sensing) can be easily connected to a mA or a volt input.

The recorders have a large memory capacity for storage of 480,000 readings. They can operate independently, without a PC. Data can be stored in this memory using sampling intervals varying from 1x per second to 1x per 24 hours. The sampling interval selected will apply to all channels. It is possible to store the data on the hard disk of a PC during measuring and recording. The transfer of recorded data takes place via an RS-232 or RS-485 communication interface with the PC (or via a modem). The data stored on hard disk can be analyzed and printed using Windows ® software.

If there is a power failure, the recorder will stop collecting measured data. Until the moment of a power failure, the date and time of the failure will be stored in a backup battery, along with the recorded data. After the power has been restored, the ATM units will automatically resume their measurements.

Display, alarm and network (only for MS3+ and MS4+)

The actual readings of the various inputs are displayed on the convenient LCD screen on the ATM-03 and the ATM-04 units. All readings can be displayed one by one using the function keys. In addition, there are four LED’s to show the status of the power voltage and the memory (exceeding 75% and 100% full). These status indicators are also announced by a sound signal.

The MS3+ and MS4+ units have extensive features for alarm signaling. Each input has 2 independently adjustable alarm set points with adjustable hysteretic and time delay.

An alarm is announced both audibly (buzzer) and visually (LED 1 to 32). The MS3+ has 1 relay, and the MS4+ unit has 16 relays, available to send signals to a central signaling system or to activate a telephone dialer. In addition, multiple MS+ units can be networked via an RS485 interface.

MS2+ 1 to 16 channel recorder
		Size: Weight: Communication: Display: Alarm signalling: Alarm output: Network:	220 x 180 x 90mm (w x h x d) 800gr. RS232 - - - -
Order No.		Model	Daten-Recorder Decription		Manual
W07-100-100		M0002-MS2+	Data Recorder / Logger unit
MS3+ 1 to 16 channel recorder LCD display + alarm (Trigger-Function) (1 relay output )
		Size: Weight: Communication: Display: Alarm signalling: Alarm output:	220 x 180 x 90mm (w x h x d) size when using thermoouple input modules: 250 x 320 x 110mm (w x h x d) 800gr. RS232 and RS485 2-row alpha numeric LCD - optical (2 LEDs per channel) - audible (built-in buzzer) 1 relay contact (230VAC/6A)
Order No.		Model	Daten-Recorder Decription		Manual
W07-100-110		M0002-MS3+	Data Recorder / Logger unit
MS4+ 1 to 16 channel recorder LCD display + alarm (16 relay outputs) + network
		Size: Weight: Communication: Display: Alarm signalling: Alarm output: Network:	250 x 320 x 110mm (w x h x d) 2000gr. RS232 and RS485 2-row alpha numeric LCD - optical (2 LEDs per channel) - audible (built-in buzzer) 1 relay contact (230VAC/6A) multiple units can be daisy chained via RS485 interface
Order No.		Model	Daten-Recorder Decription		Manual
W07-100-120		M0002-MS4+	Data Recorder / Logger unit
Overview input modules (random configurations possible)
Input module A0 4 to 20mA		Counter input module CTU	Opened MS3+ with 14 installed input modules
Order No.	Model	Measured value	Accurycy	Note
DC-Current-Module without galvanic isolation
W07-100-150	M1001-A0	dc current 4 to 20 mA	±0.1% FS	With source approximately 21V for two-wire transducers with current loop (e.g. temperature and humidity transducers Comet). Only galvanic not isolated.
W07-100-160	M1002-A1	dc current 4 to 20 mA	±0.1% FS	for passive sensing of current
W07-100-170	M1002-B0	DC current 0 to 20mA	±0.1% FS	without galvanic isolation
W07-100-180	M1002-B1	DC current 0 to 1A	±0.1% FS
W07-100-190	M1002-B2	DC current 0 to 5A	±0.1% FS
DC-Current-Module with galvanic isolation
W07-100-165	M1025-A1G	DC current 4 to 20mA	±0.1% FS	galvanic isolated
W07-100-175	M1026-B0G	DC current 0 to 20mA	±0.1% FS
W07-100-185	M1027-B1G	DC current 0 to 1A	±0.1% FS
W07-100-195	M1028-B2G	DC current 0 to 5A	±0.1% FS
AC-Current-Module with galvanic isolation
W07-100-196	M1006-C0G	DC current 0 to 20mA	±1% FS	galvanic isolated
W07-100-206	M1007-C1G	DC current 0 to 1A	±1% FS
W07-100-200	M1008-C2G	DC current 0 to 5A	±1% FS
DC-Voltage-Module without galvanic isolation
W07-100-215	M1009-D0	DC voltage to 100mV	±0,1% FS	without galvanic isolation
W07-100-225	M1010-D1	DC voltage 0 to 1V	±0,1% FS
W07-100-235	M1011-D2	DC voltage 0 to 10V	±0,1% FS
W07-100-245	M1012-D3	DC voltage 0 to 400V	±0,1% FS
DC-Voltage-Module with galvanic isolation
W07-100-210	M1029-D0G	DC voltage to 100mV	±0,1% FS	galvanic isolated
W07-100-220	M1030-D1G	DC voltage 0 to 1V	±0,1% FS
W07-100-230	M1031-D2G	DC voltage 0 to 10V	±0,1% FS
W07-100-240	M1032-D3G	DC voltage 0 to 400V	±0,1% FS
AC-Voltages-Module with galvanic isolation
W07-100-250	M1013-E0	AC voltage to 100mV	±0,1% FS	galvanic isolated
W07-100-260	M1014-E1	AC voltage 0 to 1V	±0,1% FS
W07-100-270	M1015-E2	AC voltage 0 to 10V	±0,1% FS
W07-100-280	M1016-E3	AC voltage 0 to 400V	±0,1% FS
Resitor-Module without galvanic isolation
W07-100-300	M1017-F	measurement of resistance (specify the range)	±0.1% FS	two-wire connection
Resistor-Module with galvanic isolation
W07-100-305	M1017-FG	measurement of resistance (specify the range)	±0.1% FS	two-wire connection galvanic isolated
Temperature-Module for Ni1000, Pt100 and Pt1000 without galvanic isolation
W07-100-310	M1018-J	input for Nickel RTD temperature sensor Ni1000, 6180 ppm/°C, range -50 to +250°C	-50°C to +100°C ±0.2°C 100°C to 250°C ±0.2% from reading	without galvanic isolation
W07-100-320	M1019-K	input for Platinum RTD temperature sensor Pt100, range -140 to +600°C	-140°C to +100°C ±0.2°C 100°c to 600°C ±0.2% from reading	two-wire connection without galvanic isolation
W07-100-330	M1020-K1	input for Platinum RTD temperature sensor Pt1000, range -140 to +600°C	-140°C to +100°C ±0.2°C 100°c to 600°C ±0.2% from reading	two-wire connection without galvanic isolation
Temperature-Module for Ni1000, Pt100 and Pt1000 with galvanic isolation
W07-100-340	M1034-JG	input for Nickel RTD temperature sensor Ni1000, 6180 ppm/°C, range -50 to +250°C	-50°C to +100°C ±0.2°C 100°C to 250°C ±0.2% from reading	without galvanic isolation
W07-100-350	M1035-KG	input for Platinum RTD temperature sensor Pt100, range -140 to +600°C	-140°C to +100°C ±0.2°C 100°c to 600°C ±0.2% from reading	two-wire connection with galvanic isolation
W07-100-360	M1036-K1G	input for Platinum RTD temperature sensor Pt1000, range -140 to +600°C	-140°C to +100°C ±0.2°C 100°c to 600°C ±0.2% from reading	two-wire connection with galvanic isolation
Temperature-Module for Thermocouple Type K, J. S und B without galvanic isolation
W07-100-410	M1021-N	thermocouple K (NiCr-Ni) range -70 to +1300°C	±(0.3% + 1°C) from reading	linearized, cold junction compensation .without galvanic isolation
W07-100-420	M1022-O	thermocouple J (Fe-Co) range -200 to 750°C	±(0.3% + 1°C)from reading
W07-100-430	M1023-P	thermocouple S (Pt10%Rh-Pt), range 0 to 1700°C	±(0.3% + 1°C) from reading
W07-100-440	M1024-Q	thermocouple B (Pt30%Rh-Pt), range +100 to +1800°C	±(0.3% + 1°C) from reading
Temperature-Module for Thermocouple Type K, J. S und B with galvanic isolation
W07-100-415	M1037-NG	thermocouple K (NiCr-Ni) range -70 to +1300°C	±(0.3% + 1°C) from reading	linearized, cold junction compensation .with galvanic isolation.
W07-100-425	M1004-OG	thermocouple J (Fe-Co) range -200 to 750°C	±(0.3% + 1°C)from reading
W07-100-435	M1039-PG	thermocouple S (Pt10%Rh-Pt), range 0 to 1700°C	±(0.3% + 1°C) from reading
W07-100-445	M1040-QG	thermocouple B (Pt30%Rh-Pt), range +100 to +1800°C	±(0.3% + 1°C) from reading
Binary-Input Module
W07-100-450	M1041-S	binary input for potential-less contacts. Maximum resistance of closed contact: 1000 ohms minimum duration for recording: 200ms
W07-100-460	M1042-S1	binary voltage input. Voltage for "switched ON" state: 3 to 30Vdc, input current in the"switched ON" state: 1 to 9mA-depending on the applied voltage, minimum duration for indication of change: 200ms, galvanic isolated
Counter-Module
W07-100-500	M1044-CTU	counter input for voltage signal. Voltage for "HIGH" state (for counter status change): 3 to 24Vdc maximum pulse frequency 5kHz, backed-up operation, galvanic isolated
W07-100-510	M1042-CTK	counter input for potential-less contacts and open collector. Maximum pulse frequency 5kHz, programmable filter of pulse ringing, backed-up operation during power mains failure, maximum resistance of closed contact: 10 kohms minimum resistance of open contact: 250 kohms, galvanic unisolated
Frequency -Counter Modue
W07-100-550	M1047-FU	input for measurement of frequency of voltage. Signal 0 to 5kHz, resolution 1Hz, accuracy ±(0.2% from reading + 1Hz) input voltage for state "H": 3 to 24Vdc input current in state "H": approximately 7mA minimum duration of input impuls: 30us, galvanic isolated
W07-100-560	M1048-FK	input for measurement of frequency of contact switching. 0 to 5kHz, resolution 1Hz, accuracy ±(0.2% from reading + 1Hz) maximum resistance of closed contact: 10 kohms minimum resistance of open contact: 250 kohms, minimum duration of input pulse: 30us, galvanic unisolated
Input for serial signal RS485 for devices upporting Advantech protocole
W07-100-550	M104-RS	input for serial signal RS485 for devices supporting Advantech protocole. E.g. measurement from transmitters with RS485 digital output connected to the serial RS485 network - ADAM Advantech protocol , galvanic isolated

Probes for Data-Loggers / Data recorders Series MS+
		Temperature Probes with Pt1000 3850ppm Sensors for Data Loggers Series MS+
Order No.	Model	Description	Data sheet
W14-100-xxx		Pt1000 3850ppm Probes
Temperature Transducers with 4 - 20mA output for Data-Loggers / Data recorders Series MS+
		Indoor and Outdoor Temperature Transducers with 4 -20mA output
Order No.	Model	Description	Data sheet
x	P41xx	Indoor Temperature Transducers with 4 -20mA output
x	P01xx	Outdoor Temperature Transducers with 4 -20mA output